They are making several great points related to How to Install a Bathtub in general in the content which follows.
Installing a bath tub isn't specifically rocket science, but it does call for strong plumbing, woodworking, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a moderately hard job. If the old tub is easily available, the task can move speedily; if you have to open up a wall to eliminate the old bathtub and place the brand-new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to leave the old bathtub and also embeded in the new one. Ensure you have certified on your own for the work and also fit trying it. Rather than hiring a specialist to take control of a halfway-completed job, it is much better to think about utilizing one before you begin. Chances are you might require a professional plumber to make tube links.
This write-up will certainly aid you mount a brand-new bathtub in your shower room if you have already bought a brand-new tub and also don't require to alter the arrangement of your previous water pipes.
Your devices and product checklist must make up the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installment, then the first thing you ought to do is separate the supply of water. After doing so, turn on the taps to drain pipes any water staying in the system. The procedure of eliminating the existing taps can be rather troublesome because of the restricted gain access to that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a fabric prepared for the remaining water that will originate from the pipes. As soon as the supply pipelines have been removed, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this procedure. Once the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will need a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the tap and the other end supplies a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the placing opening in the bath/basin making sure that the washers remain in place between the faucet as well as the sink. Safeguard the tap in position with the manufacturer supplied backnut. Once the tap is safely in position, the supply pipes can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular tap ports. The previous kind needs to be connected to the tap ends first, tightening just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Tub
Using the two wooden boards under its feet, place the bath tub in the needed position. The wooden boards are practical in evenly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next objective is to guarantee that the tub is leveled all round. This can be accomplished by examining the spirit level as well as changing the feet on the bathtub up until the level reads degree.
To install taps, fit all-time low of the furthest adaptable tap connector to the proper supply pipe by making a compression join; after that do the same for the various other tap.
Activate the supply of water and also examine all joints and new pipework for leaks as well as tighten them if essential. Fill the bathtub and also check the overflow outlet and the normal outlet for leaks.
Finally, fix the bathroom paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub should wait till the tub has been used at the very least when as this will resolve it into its last setting.
Getting ready for the Installation
To start with, the supporting framework supplied with the bathroom should be fitted (if needed) according to the manufacturer's directions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the tap features a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps system to avoid pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its final setting.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack an inflexible seal, causing the water to permeate the wall between the bathroom and also the tiling, leading to complications with wetness and also possible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and also cartridges, as well as are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to enable the activity experienced when the bathtub remains in usage. The sealer can split relatively very early if you do not take into account this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently readily available on the market. It is a good idea to fit the tiles utilizing water-resistant or water-proof sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was brought to that report about Installing A Bathtub from a good friend on our other blog. Are you aware of somebody who is fascinated about How to Install a Bathtub Yourself? Please feel free to share it. Thank-you for taking the time to read it.
For quick relief, contact!